Electronic bistable impulse relay BIS-419i 230 V

Electronic bistable impulse relay BIS-419i 230 V

BIS-419i 230 V

The electronic bistable relay enables switching on the lighting or other device from several different points by means of parallel connected control buttons.
Sequential. Power supply 230 V AC . Maximum load 2 x 16 A (160 A / 20 ms). On the 35 mm rail. Can be used with backlit buttons.

BIS-419i 230V is available in versions:

  • BIS-419 230 V - basic model with a single 16 A relay
  • BIS-419i 230 V - with contact adapted to work with receivers with a large starting current, such as: LED lamps, ESL fluorescent lamps, electronic transformers, discharge lamps, etc.

Purpose
Electronic bistable pulse relay enables switching on or off the lighting or other device from several different points by means of parallel connected, momentary (bell) control switches.
The BIS-419 relay has two switching sections and enables two circuits (branches) of lighting or other receivers to be connected according to the selected sequence from several different points.
 

Functioning
Power supply of the relay is signaled by the green LED. The sequential relay has two separate outputs R1 and R2. The contact status (closed / open) is forced sequentially according to the given program. Switching the contacts into the next state follows the next pulse of the control button. Switching on contact R1 and R2 is signaled by lighting of the corresponding red LEDs R1 and R2. After a power failure, the contact status is reset. After restarting the supply voltage, the relay starts operation from sequence No. 0.
 

Work functions

Function A


 
   

Subsequent presses of the button repeat sequence 0-3.
 

Function B

* Repeatedly pressing the button in less than 5 seconds, repeats sequences 1-3.
* The next pressing of the button after a time longer than 5 s, disconnects both contacts (sequence 0).
* Long press of the button - in any sequence - disconnects both contacts (sequence 0).
* After switching off both relays, pressing the button again restores the state before the shutdown (state memory). It does not apply to the case of power failure of the relay.
 

Function C

Subsequent presses of the button repeat sequence 0-3.
 

Function D


 

* Repeatedly pressing the button in less than 5 seconds, repeats sequences 1-3.
* The next pressing of the button after a time longer than 5 s, disconnects both contacts (sequence 0).
* Long press of the button - in any sequence - disconnects both contacts (sequence 0).
* After switching off both relays, pressing the button again restores the state before the shutdown (state memory). It does not apply to the case of power failure of the relay.
  

Attention!
The BIS-419i 230V is compatible with bell pushes equipped with fluorescent lamps.     

Power supply voltage165├Ě265 V AC
Local controlYES
Maximum AC-1 load current2 x 16 A
The executive elementrelay
Contact configuration2 ├Ś NO
Separation of the contactYES
Resistance to shock currentsYES
Number of channels2
functionalitysequential
Delay of operation0,1 ├Ě 0,2 s
Control pulse currentless than 5 mA
Cooperation with illuminated buttonsYES
terminalscrew terminals 2,5 mm┬▓
Tightening torque0,4 Nm
Power consumption waking / working0,15 W/0,9 W
Working temperature-25 ├Ě 50 ┬░C
dimensions1 module (18 mm)
Assemblyon rail 35 mm
Level of securityIP20
Przyciski pod┼Ťwietlane
W przypadku pod┼é─ůczenia zbyt du┼╝ej ilo┼Ťci przycisków pod┼Ťwietlanych mo┼╝e dochodzi─ç do samoistnego za┼é─ůczania o┼Ťwietlenia lub za┼é─ůczenia o┼Ťwietlenia na sta┼ée.

Maksymalny pr─ůd obci─ů┼╝enia
Pr─ůd styku podany w danych technicznych jest warto┼Ťci─ů maksymaln─ů i mo┼╝e podlega─ç ograniczeniom – wi─Öcej informacji. Je┼Ťli z przedstawionych informacji wynika, ┼╝e przeka┼║nik w urz─ůdzeniu jest niewystarczaj─ůcy zaleca si─Ö stosowa─ç zewn─Ötrzny element prze┼é─ůczaj─ůcy (np. stycznik) przystosowany do prze┼é─ůczania du┼╝ych pr─ůdów udarowych.


Pami─Ö─ç stanu
Przeka┼║nik nie posiada "pami─Öci" pozycji styku. Oznacza to, ┼╝e po za┼é─ůczeniu zasilania styk przeka┼║nika zawsze pozostanie w stanie wy┼é─ůczonym.

Odporno┼Ť─ç na pr─ůdy udarowe
W urz─ůdzeniu zastosowany zosta┼é przeka┼║nik typu "inrush" charakteryzuj─ůcy si─Ö du┼╝─ů wytrzyma┼éo┼Ťci─ů na krótkotrwa┼ée pr─ůdy udarowe powstaj─ůce np. w momencie za┼é─ůczenia lamp LED, ┼Ťwietlówek ESL, tranformatorów elektronicznych, lamp wy┼éadowczych itp.

30 other products in the same category: