Electronic bistable impulse relay BIS-419 230 V

Electronic bistable impulse relay BIS-419 230 V

BIS-419, 5908312598046

Product description

Electronic bistable pulse relay switch that turns on or off lights or other equipment from several different points with the parallel connected momentary (bell) control switches.

Sequential. 4-function. Power supply 230 V AC. Maximum load 2 x16 A. On TH-35 mm rail. Can be used with backlit buttons.

BIS-419 relay has two switching sections and allows for switching of two lightning circuits or others receivers from several different points and in accordance with the preselected sequence.

Operation
The relay power supply is indicated by a green LED U. Sequential relay has two separate outputs: R1 and R2. Contact status (closed/open) is forced sequentially in accordance with a predetermined program. Contacts switch to another state after subsequent pulse from control button. R1 and R2 contact activation is indicated by the relevant R1 and R2 red LED. After a power failure, contact state is reset. When the power is back on, the relay starts from the sequence number 0.
 

Note!
BIS-419 230 V can be used with backlit buttons.    
 

Working function

Function A


 
   

Pressing the button subsequently repeats sequences 0-3.
 

Function B

* Pressing the button subsequently in less than 5 seconds  repeats sequences of 1-3.
* Subsequent pressing of the button after more than 5 seconds disconnects both contacts (sequence 0).
* Long press - in any sequence - disconnects both contacts (sequence 0).
* Pressing the button after both relays were turned off restores the last state (memory of state). Does not apply in the case of a relay power failure.
 

Function C

Pressing the button subsequently repeats sequences 0-3.
 

Function D


 

* Pressing the button subsequently in less than 5 seconds  repeats sequences of 1-3.
* Subsequent pressing of the button after more than 5 seconds disconnects both contacts (sequence 0).
* Long press - in any sequence - disconnects both contacts (sequence 0).
* Pressing the button after both relays were turned off restores the last state (memory of state). Does not apply in the case of a relay power failure.
 

Table of power


 

These data are indicative and will heavily depend on the design of a specific receiver (that is especially important for LED bulbs, energy-saving lamps, electronic transformers and pulse power supply units), switching frequency and operating conditions.



Power supply voltage165÷265 V AC
Local controlYES
Maximum AC-1 load current2 x 16 A
The executive elementrelay
Contact configuration2 × NO/NC
Separation of the contactYES
Resistance to shock currentsNO
Number of channels2
functionalitysequential
Delay of operation0,1 ÷ 0,2 s
Control pulse currentless than 5 mA
Cooperation with illuminated buttonsYES
Terminalpluggable terminal blocks 2,5 mm²
Tightening torque0,4 Nm
Power consumption waking / working0,15 W/09 W
Working temperature-25 ÷ 50 °C
Dimensions1 module (18 mm)
Assemblyon rail 35 mm
Ingress Protection MarkingIP20
Przyciski podświetlane
W przypadku podÅ‚Ä…czenia zbyt dużej iloÅ›ci przycisków podÅ›wietlanych może dochodzić do samoistnego zaÅ‚Ä…czania oÅ›wietlenia lub zaÅ‚Ä…czenia oÅ›wietlenia na staÅ‚e.

Maksymalny prąd obciążenia
PrÄ…d styku podany w danych technicznych jest wartoÅ›ciÄ… maksymalnÄ… i może podlegać ograniczeniom – wiÄ™cej informacji. JeÅ›li z przedstawionych informacji wynika, że przekaźnik w urzÄ…dzeniu jest niewystarczajÄ…cy zaleca siÄ™ stosować zewnÄ™trzny element przeÅ‚Ä…czajÄ…cy (np. stycznik) przystosowany do przeÅ‚Ä…czania dużych prÄ…dów udarowych.


Pamięć stanu
Przekaźnik nie posiada "pamięci" pozycji styku. Oznacza to, że po załączeniu zasilania styk przekaźnika zawsze pozostanie w stanie wyłączonym.